a DE Puzzle
I recently loaded a .357 mag load with HS7, a powder I like that is also good for 44 mag. It shot very nicely out of my 6 inch barrel. When I put the 10-inch barrel on, it would extract/eject just...
View ArticleRe: a DE Puzzle
I had typed in a reply but my STUPID IP disconnected me & all is lost! What I will say is that if an individual attempts to make alterations to a firearm I would hope that they are "competent"...
View ArticleRe: a DE Puzzle
Thanks for all replies - very good discussion. Oe question - how are we defining slow burning powder? H110 is slow for handguns use, but works very well in DEs. I will probably tinker wiht the load a...
View ArticleRe: a DE Puzzle
Blu, I have the 3 barrel setup for my .357 D.E.. I am having the same problem. One thing I noticed using the cleaning tool supplied is different piston chamber sizes. The 6 inch barrel has a tight fit...
View ArticleRe: a DE Puzzle
Let me get this straight!So the reason for DE won't extract right is because the pressure build up in the bolt. And the slide won't work properly with pressure on the bolt. But the problem that i have...
View ArticleRe: a DE Puzzle
Because it tends to slow the bolt down ( especially on the lighter .357 Magnum ) riping it's self loose or in other words, it's actually managing to get the shell out dispte the preasure but loosing...
View ArticleRe: a DE Puzzle
it is possible.the nice thing about having a forum like this dedicated to the de,is that just about every possible senario is covered by the members.I still would suggest trying to drop a complete...
View ArticleRe: a DE Puzzle
Where can you order a modified piston to replace the current one?I have a 44mag and this little problem is drivinh me nuts. Besides from that i love everything about the gun.
View ArticleRe: a DE Puzzle
No one on earth can fix your piston properley without the in tact and functional firearm on hand. Their is no way they can know how much to trim it without fireing the gun themselves or runing the...
View ArticleRe: a DE Puzzle
I think my gun has this kinda of problem i will call MRI tomorrow to see what they can do for me.The problem happens on the third round. The first round is cycled by hand so there is no problem with...
View ArticleRe: a DE Puzzle
It is the round piston that attaches to the requail bar through the slide and fits in the big hole under the barrel. Now, the chambering problem and the one you have may not be the same. The DE is...
View ArticleRe: a DE Puzzle
Ok thanks 44 CannonI think i'm gonna order a new set of spring and a new mag just to test it out.
View ArticleRe: a DE Puzzle
wl125:I was having the same style jam you are having. However, I polished the feed ramp on the frame and then the feed ramp on the barrel. Upon close inspection, prior to polishing, I didn't see...
View ArticleRe: a DE Puzzle
wl125:I'm having a bit of trouble following your description.... is this correct:1. First round manually cycles fine.2. Second round cycles but doesn't completely chamber?3. After firing second round,...
View ArticleRe: a DE Puzzle
You got it!Nope, nothing is the touching the magazine during the firing process.And this sort of jamming is happening to every third round, and all the shells are damaged pretty badly with out firing...
View ArticleRe: a DE Puzzle
Sounds to me like the feed angle of the magazine would be a big suspect here, then...
View ArticleRe: a DE Puzzle
wl125:Did you try a new mag yet? I know the original mag that came with my DE needed some filing to get it right. I didn't figure this out until, I bought another mag. Now that I think about it.......
View ArticleRe: a DE Puzzle
what do you use to polish the inside?I checked the entire chamber area where a round would touch to see if there has been any metalic contacts. I would also try to smoothen out the magazine where the...
View Article
